Welcome To Sphere Research's Canadian Test Equipment & Parts Site! | ||||
![]() Click REFRESH on your browser if pages seem unchanged ![]() Everything from Quotes and SciFi to Ethics & Business. ![]() ![]() ![]() | ![]() |
Sphere Research Corporation 3394 Sunnyside Rd. West Kelowna, BC, Canada V1Z 2V4 Phone: +1 (250) 769-1834 FAX:+1 (250) 769-4106 A great source for test equipment, repairs, calibrations, useful metrology information, and of course, SLIDE RULES! Just ![]() |
I'm in a HURRY! Show me all the: | ![]() |
![]() |
![]() |
![]() |
Tektronix 348 Series Feet + Newly Designed Replacements
![]() With the help of aerospace mechanical friends at Helimec, Sphere has come up with a drop in fix for this problem that replaces the old foot, while adding more mechanical strength, and allows an optional anti-slip feature to be installed. The design time and cost was donated to the Tek community to allow these great instruments to stay in service. The cost of the set of replacement feet is the actual raw material cost plus 10 percent to allow recovery of parts and material shipping and ordering. The new foot is made of ABS, the screw is a mil-spec passivated steel screw (2 inches long), and the anti-skid insert is rubber. You can see full details of the new design below. ![]() Because these were created to allow us to restore instruments, we will have some used original Tek 348-0339-00 feet available as well which we will post here. There will not be too many of these, and we will offer only those in good condition. We will also post all the other Tek equipment feet we get to this same page for your convenience. Both the original and new feet are made in the USA. You can order anything here just by picking up the phone, and calling (250) 769-1834 during normal office hours, 8:30AM to 4:30PM PST, OR, Email your order to Susan ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() Don't forget these illustrated sections take a few seconds to load, but they are worth the wait!
|
Helimec 339 Foot Kit![]() CLICK for bigger Pic ![]() CLICK for bigger Pic ![]() |
SORRY, SOLD OUT WE ARE UNABLE TO SUPPLY ANY LONGER The Helimec 339 Rear Foot is a replacement for the Tek 348-0339-00 foot and 212-0020-00 screw. One kit (4 Feet, 4 Screws, 4 Anti-skid bumpers) replaces one set of 4 Tek feet and screws directly. The anti-skid rubber insert is not mandatory, but provides a replaceable wear surface, and significantly increases the instruments stability when operated vertically. These are normally ordered and replaced as a set of 4. Due to a slight height difference, single replacements would make the scope sit unevenly, and are NOT recommended. An END VIEW, old on the left, new on the right and below. Installed Pictures (465B) (CLICK for bigger Pics) ![]() ![]() Original Foot Pictures (465B) (CLICK for bigger Pics) ![]() |
![]() Price: US$39 for set of 4 ![]() ![]() CLICK TO ORDER |
Tek 348-0080-01![]() CLICK for bigger Pic ![]() |
These are NEW, late production Tek 348-0080-01 bottom feet. These are in very limited supply, and no more than 4 can be sent to any one customer. These have a captive nuts. These are sold BY EACH FOOT. These can be shipped very cheaply in a padded bag. | ![]() Have: 4 Price: US$5 Each ![]() ![]() CLICK TO ORDER |
Tek 348-0272-00![]() CLICK for bigger Pic ![]() |
These are NEW, Tek 348-0272-00 rear feet. These are in very limited supply, and no more than 4 can be sent to any one customer. These are incredibly tough, and I think are used in the 434. These are sold BY EACH FOOT. | ![]() Have: 5 Price: US$15 Each ![]() ![]() CLICK TO ORDER |
Tek 348-0339-00![]() ![]() |
These are used, clean Tek 348-0339-00 rear feet and may or may not also have 212-0020-00 screws. These are in very limited supply, and no more than 4 can be sent to any one customer. We have these only when we have scrapped a scope or exchanged feet with our new Helimec feet above and have good feet left to offer. These are sold BY EACH FOOT. 348-0339-00 Foot Pictures (465B) (CLICK for bigger Pics) ![]() |
SORRY, SOLD Price: US$12 Each ![]() ![]() CLICK TO ORDER |
Tek 348-0420-01![]() CLICK for bigger Pic ![]() |
These are NEW, Tek 348-0420-01 back bumpers. These are used on the back of later scopes. These are sold BY EACH BUMPER. | ![]() Have: 26 Price: US$10 Each ![]() ![]() CLICK TO ORDER |
Tek 384 7K Feet![]() ![]() |
These are used, clean Tek 348-series botton feet from (I think) 7K series scopes and some related chassis items. The foot is a hard plastic, with a rubber insert for the non-skid surface, and has two screw holes for mounting. These may have right/left orientation, as I see they have tilt bale inserts. I have some hardware for these too. I will try and find the correct part number. These are sold BY EACH FOOT. | Have: 4 Price: US$10 Each ![]() ![]() CLICK TO ORDER |